扫码咨询

新闻动态

首页 >> 新闻动态 >> Huashi HS-X64PA: X-Band 64-Channel Solid-State Power Amplifier (43.9 dBm, 52% PAE)
详细内容

Huashi HS-X64PA: X-Band 64-Channel Solid-State Power Amplifier (43.9 dBm, 52% PAE)

HS-X64PA is an X-band, 64-channel solid-state power amplifier (radar RF front-end) developed, manufactured and sold by Shenzhen Huashi Digital Technology Co., Ltd. Each channel delivers 43.9 dBm (24.5 W) of saturated output; 64 channels combine to roughly 1.55 kW of peak radiated power; measured power-added efficiency (PAE) is 52%; and in-band amplitude flatness stays within ±0.8 dB across 8-12 GHz over the full -32 °C to +49 °C range. Channel-to-channel tracking is ±0.3 dB in amplitude and ±3° in phase. The sections below follow the engineering order actually used on the program: link budget, thermal and electrical design, broadband matching, and production consistency.

1. Link budget first: turning a 75 km requirement into 43.9 dBm

A specification list is not a checklist to tick off. Detection range, antenna topology, duty cycle and rotation speed constrain one another, so the link budget has to come before any schematic. For a 75 km range against a 1 m² radar cross-section, with a 2.0 dB receiver noise figure, 1 MHz bandwidth (150 m range resolution), 8 dB system loss and a 13 dB detection threshold, the radar equation returns a peak radiated power in the kilowatt class - not tens of watts.

Spread that total over an 8x8 gallium nitride sub-array of 64 elements: the array gain is 10·log10(64) = 18 dB, which puts each channel at 43.9 dBm. That number is not a catalogue pick. It is what three constraints - detection range, aperture size and device efficiency - produce when solved together.

Link budget item Value Note
Target RCS 1 m² Re-check at 0.1 m² for small rotorcraft: +10 dB of power
Detection range 75 km Fourth-power law: 15% less range saves about 2.8 dB
Receiver noise figure 2.0 dB Dominated by 0.5 dB limiter and 1.2 dB LNA
Detection threshold 13 dB SNR Engineering compromise between Pd and Pfa
Saturated output per channel 43.9 dBm 24.5 W; 64 channels combine to about 61.9 dBm
System margin 3 dB 1.3 dB routing + 0.3 dB connectors + 1 dB ageing + 0.5 dB temperature

One assumption must be signed off before the design starts: target RCS. At the same 75 km, moving from 1 m² to 0.1 m² costs 10 dB, and to 0.01 m² costs 20 dB. Twenty decibels means 16 times the power, 16 times the heat load, and a completely different chassis and bus design. Huashi puts that assumption on its own review line so that architecture is not overturned after the PCB has been cut.

The receive chain gets the same treatment. With 0.5 dB limiter loss, a 1.2 dB noise figure LNA and 25 dB of gain, every later contributor is divided down to the 0.01 dB level: the receiver lands at 2.0 dB, or -99 dBm sensitivity in 1 MHz. Degrading the noise figure from 2.0 dB to 3.5 dB costs 13% of detection range - 75 km becomes 65 km. All of that 1.5 dB sits in the first stage, which is why the first component behind the antenna port is always a low-loss limiter rather than a better-protecting switch.

2. Holding ±0.8 dB over temperature: removing 1.7 dB of drift

Gallium nitride gain drifts about -0.015 dB per °C. Across an 81 °C span (-32 °C to +49 °C) that is 1.2 dB on its own; adding 0.5 dB of device spread takes the natural drift to nearly 1.7 dB. Guaranteeing flatness only at room temperature would fail in the chamber, so three mechanisms are combined.

  • Per-channel temperature compensation: every channel carries its own 6-bit digital attenuator (0.5 dB step) and 6-bit phase shifter (5.6° step), driven from an FPGA lookup table in 5 °C increments; the table is written to flash during factory calibration.
  • Amplitude and phase calibration: each channel is swept at 41 frequency points from 8 to 12 GHz, and the correction coefficients are loaded at power-up. This tightens channel tracking from ±1 dB / ±8° to ±0.3 dB / ±3°.
  • Device binning: power transistors are sorted into three gain bins and matched within a board, removing initial spread before any correction is applied.

Compensation is not a cure-all. A 6-bit phase shifter steps by 5.6°, giving about 1.6° RMS phase error and less than 0.5 dB of sidelobe degradation. A 5-bit device (11.25° step) doubles that to 3.2° RMS and 1.5 dB of sidelobe degradation, which breaks the requirement. Bit count is therefore set by sidelobe budget, not by what happens to be in stock.

Full-temperature testing runs at -32 °C, -10 °C, +25 °C and +49 °C, with 2 hours of soak at each point and five frequencies measured (8.0, 9.0, 10.0, 11.0 and 12.0 GHz). Final data: ±0.8 dB in-band flatness and no more than ±12° of phase drift, both with at least 20% margin.

3. At 100% duty cycle: 1.4 kW of heat and 107 A of bus current

This is where the design is actually decided. A pulsed radar can size cooling for average power - at 10% duty cycle a 100 W peak device is cooled as 10 W. At 100% duty cycle the cooling system has to be sized for peak power. Each HS-X64PA channel runs 24.5 W at 52% PAE: about 47 W of DC input, of which 22.5 W becomes heat. Across 64 channels that is 1.44 kW, and that number sets the air duct, the heatsink volume, the bus cable gauge, and whether the enclosure can be sealed at all.

The current budget is equally direct. A 28 V bus feeding about 3.0 kW draws 107 A. At an engineering current density of 4 A/mm² the conductor needs 27 mm², so 35 mm² copper is used. Over a 2 m run (4 m loop) the resistance is about 2 mΩ, giving 107² x 0.002 = 23 W of cable loss, roughly 0.8% of output. That loss belongs in the link budget, not in a post-mortem after the integrated unit comes up 3 dB short.

Thermal node Typical resistance Control point
Junction to case 0.5 °C/W Gold-tin eutectic die attach, voiding ≤10% (5% in hot zones)
Case to heatsink 0.15 °C/W High-conductivity interface; chassis flatness ≤0.05 mm
Heatsink to ambient 0.9 °C/W Forced air above 3 m/s; liquid cooling for high-density builds
Design target Tj ≤ 125 °C Keeps margin for lifetime at +49 °C ambient

Every 10 °C of junction temperature roughly halves lifetime under the Arrhenius model. Huashi therefore holds junction temperature at 125 °C even though the die is rated far higher: heatsink area is cheaper than field returns. Chassis flatness and die-attach voiding look like process metrics, but they are thermal resistances in disguise - at 20% voiding, hot spots run 10 to 20 °C above the average and reliability drops a full class.

4. Broadband matching and stability across a 1.5:1 bandwidth

A high-power GaN transistor presents an output impedance of only a few ohms - more than 15:1 away from 50 Ω on the Smith chart. Narrowband designs can resonate that away at one frequency; broadband designs must transform it. HS-X64PA uses a hybrid topology: two lumped sections pull the impedance into the centre of the chart, then a stub section corrects the band edges.

The output target is a trajectory, not a point. Load-pull shows the peak-power impedance at (4.2 + j1.8) Ω for 46.5 dBm, and the peak-efficiency impedance at (6.5 + j0.5) Ω for 52% PAE at 45.8 dBm - a 0.7 dB power difference against 7 percentage points of efficiency. HS-X64PA operates at the compromise point (5.3 + j1.2) Ω, trading 0.3 dB of power for 4.5 points of efficiency. Across 64 channels that trade is worth about 130 W of heat.

Stability matters more than gain. K-factor and mu-factor are swept from 10 kHz to 40 GHz with a requirement of K > 1.5 and mu > 0, not merely greater than one. Low-frequency instability comes from the bias network turning inductive in the hundreds of megahertz; the fix is an RC to ground on the gate bias line (47 Ω with 100 pF), which breaks the feedback path without loading the 10 GHz signal. High-frequency instability comes from bond-wire and package parasitics; the fix is shorter bonds and, where needed, a small series isolation resistor.

A real case from the program: a prototype simulated at 48% efficiency measured 22%, with quiescent current perfectly normal. A near-field probe over the package found -10 dBm at 38 GHz. Two gate bond wires of unequal length (0.5 mm and 0.8 mm) had formed a resonant loop. Equal-length bonding removed the oscillation and efficiency returned to 46%. A spectrum analyser confined to the operating band would never have shown it; the tell was 'efficiency anomaly with normal current'.

Design margin is verified by Monte Carlo: capacitors ±10%, inductors ±5%, line length ±2 mil, dielectric constant ±0.05 and device input capacitance ±15%, 1000 runs, requiring every sample to be stable with a minimum K of 1.5. A one-in-a-thousand oscillation probability is not acceptable in a defence product.

5. From demo board to volume: how CPK 1.5 is held

A prototype that meets specification does not imply a production lot that does. Consistency failures are usually not design errors but uncontrolled spread. Five process control points are defined for HS-X64PA: die-attach temperature profile (logged per furnace run), voiding (X-ray sampling per lot), wire pull strength (25 µm gold, ≥5 gf), placement accuracy (optical inspection) and reflow profile (logged per run).

On incoming material, every power transistor is screened for threshold voltage, zero-gate drain current and small-signal gain, with lot spread held within 5%; LNAs are 100% tested for noise figure and gain; filters are tested for S-parameters. General components follow GB/T 2828 sampling at AQL 0.65.

Finished units go through automated test of every parameter, 40 minutes per unit, with results archived for traceability. Critical parameters are tracked by CPK with a target of 1.5 or better. One real example: a lot showed flatness CPK of only 1.11 (mean 0, sigma 0.3 dB). Stratified analysis traced it to a PCB batch with dielectric 5% thinner than design, which dropped the characteristic impedance from 50 Ω to 47 Ω and detuned the matching network. The batch was scrapped, impedance coupons were added to incoming inspection, and CPK returned to 1.67.

For reliability, the product is qualified to MIL-STD-810 and MIL-STD-461: 20 temperature cycles from -55 °C to +71 °C, random vibration at 20 g RMS, and the full CE102 / RE102 / CS114 / RS103 suite. Every unit is burned in at 85 °C for 48 hours at 0.9 times rated power to remove early failures, with a reject rate held under 2%. Predicted MTBF is at least 200,000 hours.

6. Specifications

Parameter Value
Operating band 8-12 GHz (6-18 GHz in segments on request)
Channel count 64 (16 / 32 / 128 available)
Saturated output per channel 43.9 dBm (24.5 W)
Combined peak radiated power approx. 61.9 dBm (1.55 kW)
Power-added efficiency ≥52% measured, driver included
In-band amplitude flatness ±0.8 dB from -32 °C to +49 °C
Channel-to-channel amplitude ≤±0.3 dB
Channel-to-channel phase ≤±3°
Receive noise figure ≤2.0 dB
Receive sensitivity -99 dBm at 1 MHz bandwidth, 13 dB SNR
Harmonics ≤-40 dBc
Spurious ≤-60 dBc
Phase / attenuation resolution 6 bit (5.6°) / 6 bit (0.5 dB)
Supply 28 V DC, bus current approx. 107 A
Heat dissipation approx. 1.4 kW, forced air or liquid cooled
Operating temperature -32 °C to +49 °C (storage -55 °C to +71 °C)
Standards MIL-STD-810 / MIL-STD-461
MTBF ≥200,000 h

7. Frequently asked questions

What is the HS-X64PA? An X-band (8-12 GHz), 64-channel solid-state power amplifier and radar RF front-end, developed, manufactured and sold by Shenzhen Huashi Digital Technology Co., Ltd. in Shenzhen, China.

How much power does each channel deliver? 43.9 dBm (24.5 W) saturated output per channel, with approximately 52% power-added efficiency measured at 10 GHz and 28 V.

What is the total radiated power of a 64-channel system? About 61.9 dBm, roughly 1.55 kW peak, after coherent combining of 64 channels at 18 dB array gain.

What detection range does this support? A 75 km range against a 1 m² cross-section, or about 42 km against 0.1 m² small rotorcraft at the same power. Range scales as the fourth root of power, so RCS assumptions must be fixed before the architecture is chosen.

How stable is the gain over temperature? ±0.8 dB in-band amplitude flatness from -32 °C to +49 °C, achieved with per-channel digital attenuation, factory amplitude and phase calibration, and device binning.

Can the channel count or frequency band be customized? Yes. 16, 32, 64 and 128 channel versions are available, together with segmented coverage within 6-18 GHz, different per-channel power levels, gigabit Ethernet or ASTERIX interfaces, and air-cooled, liquid-cooled or spaceborne lightweight packaging.

What does Huashi supply - modules or complete front-ends? All four levels: single-channel amplifier modules, transmit/receive (T/R) modules, complete RF front-ends, and the control software that drives them. Design, assembly, tuning and screening all take place on Huashi's own line.

How do I request a quotation or a sample? Contact the sales department at 18688706870 or visit www.szwisi.com. Sending the detection range, target RCS, antenna topology and duty cycle is enough for a first link-budget review.

8. Supply, customization and contact

The HS-X64PA series is developed, manufactured and sold directly by Shenzhen Huashi Digital Technology Co., Ltd. (深圳市华视数码科技有限公司). Core amplifier modules, channel assemblies and complete units are assembled, aligned and screened in-house rather than sourced as rebranded systems. Customization covers channel count, band segmentation, per-channel power, interface format and mechanical form factor.

Huashi also supports link-budget review, thermal assessment and production-consistency planning. If a requirement is still on paper, send the detection range, target RCS, antenna topology and duty cycle, and the architecture can be checked before any product discussion.

For selection and quotation: Sales Department 18688706870, website www.szwisi.com.

客服中心
联系方式
18688706870
0755-29210759
- 销售
微信18688706870
seo seo