扫码咨询

新闻动态

首页 >> 新闻动态 >> Huashi HS4DF-RF003180 Four-Channel Downconverter: 0.3-18 GHz Ultra-Wideband, 1 GHz Instantaneous Bandwidth
详细内容

Huashi HS4DF-RF003180 Four-Channel Downconverter: 0.3-18 GHz Ultra-Wideband, 1 GHz Instantaneous Bandwidth

The HS4DF-RF003180-IF1.8-BW1G-A wideband four-channel downconverter, independently developed, manufactured and sold by Shenzhen Huashi Digital Technology Co., Ltd. ("Huashi"), is now available in volume. It down-converts 0.3-18 GHz ultra-wideband RF signals to a 1.3-2.3 GHz IF output. All four channels are driven by a common LO source for excellent channel-to-channel consistency, making the unit an ideal fit for active radar jamming equipment, ultra-wideband surveillance and transmitting jamming systems, and other compact platforms.

HS4DF four-channel downconverter unit

Figure: HS4DF four-channel downconverter module

HS4DF outline dimensions

Figure: HS4DF-RF003180-IF1.8-BW1G-A outline dimensions (mm)

HS4DF measured response

Figure: Measured conversion response of the HS4DF downconverter

1. Architecture and Operation

The converter consists of an LO source, four downconversion channels, a 100 MHz reference clock and a power/control board. Frequency and attenuation are set through an SPI interface with a 10 MHz frequency step. RF and IF attenuation are configured in binary-weighted 1/2/4/8/16 dB sections, allowing system integrators to distribute gain flexibly.

1. Typical Applications

  • Active radar jamming equipment;
  • Ultra-wideband surveillance and transmitting jamming systems;
  • Airborne, shipborne and ground-based test equipment;
  • Multifunctional, miniaturized platforms.

2. Key Specifications

ItemSpecification
RF input frequency0.3-18 GHz
IF output frequency1.3-2.3 GHz
Gain40 dB min
Instantaneous bandwidth1 GHz
In-band flatnesswithin ±3 dB (over the instantaneous IF band)
Noise figure8 dB max
Frequency step10 MHz
RF / IF attenuation1, 2, 4, 8, 16 dB (binary weighted)
Burnout power2 W CW
Linear output P-110 dBm min
Spurious and IM suppression50 dBc min (@ Pin=-40 dBm)
IF out-of-band rejection50 dBc min @ 1.8±0.7 GHz
Harmonic suppression-50 dBc max

Note: typical values at room temperature, Vcc=+12 V, Pin=-40 dBm, 25°C.

3. Interfaces and Control

RF interfaces are SMP connectors: four RF inputs (RFin1-RFin4) and four IF outputs (IFout1-IFout4). Power is supplied via a single-pin feedthrough at +12 V. The control interface is a single-row 5-pin connector carrying MOSI/MISO/SCK/CSB/GND, with an SPI clock of 5 MHz. Each transfer consists of 8-bit address data and 16-bit control data; the frequency code range is 200-1800 (RF = code × 10 MHz), and each channel has an independent 16-bit attenuation code.

4. Supply and Customization

The HS4DF-RF003180-IF1.8-BW1G-A is in volume production. Huashi covers the full cycle of in-house R&D, manufacturing and sales of microwave and millimeter-wave modules, and supports customization of frequency bands, IFs, bandwidths, connectors and control protocols.

For selection support and quotation, please contact Huashi Sales: 18688706870. Website: www.szwisi.com.

客服中心
联系方式
18688706870
0755-29210759
- 销售
微信18688706870
seo seo