扫码咨询

新闻动态

首页 >> 新闻动态 >> 23.8-24.2 GHz 100 W GaN SSPA for K-Band Uplink: 400 MHz Narrowband, 38% PAE, 2U Rack
详细内容

23.8-24.2 GHz 100 W GaN SSPA for K-Band Uplink: 400 MHz Narrowband, 38% PAE, 2U Rack

Overview

The HS-PA K-band series is a 400 MHz narrowband GaN solid-state power amplifier engineered specifically for the 23.8–24.2 GHz uplink window. A new-generation GaN power die is combined with a low-loss multi-way spatial power-combining architecture to deliver ≥100 W saturated output in continuous wave, with margins that meet or exceed comparable products from established international vendors.

The signal chain integrates a low-noise preamplifier, multi-stage linear driver, low-loss spatial combiner, high-directivity coupler and detector, fast temperature and VSWR sensing, and intelligent protection logic — all inside a 19-inch, 2U chassis. The result is high power-added efficiency, tight in-band flatness, low harmonic and spurious content, and linear behaviour suited to complex digital modulation. The unit is built for unattended outdoor sites and 7×24 satellite gateway operation.

Typical applications

  • K-band satellite gateway uplink chains

  • 24 GHz long-haul point-to-point microwave backhaul

  • TT&C and high-rate remote-sensing transmit units

  • RF test benches and phased-array channel calibration

  • Ground terminals for LEO commercial space constellations

Design highlights

  1. Narrowband, fully optimised: 400 MHz of usable bandwidth with tight amplitude and phase consistency and steep out-of-band roll-off — no adjacent-channel interference.

  2. New-generation GaN architecture: class-leading power-added efficiency lowers heat load, which in turn reduces cooling and prime-power cost.

  3. Protection at nanosecond speed: high mismatch tolerance — the output stage survives open, short and severe load mismatch without damage to the power devices.

  4. Stable across the full temperature range: minimal gain and output drift from cold start to +65 °C; remote monitoring and multi-unit networking supported.

  5. Solid-state by design: no TWT warm-up and no filament wear — full output at switch-on, long service life and low maintenance.

RF performance (Ta = 25 °C, CW, 50 Ω system)

ParameterSpecificationNotes
Frequency range23.8–24.2 GHz400 MHz narrowband
Saturated output power, Psat≥100 W (50 dBm)Minimum guaranteed over full band
Output power at 1 dB compression, P1dB≥82 W (49.1 dBm)High linearity for complex modulation
Small-signal gain50 ± 0.8 dBReduces driver-stage requirements
In-band gain flatness≤ ± 0.4 dBAcross the full 400 MHz
Input power range−5 to +8 dBmWide input dynamic range
Input VSWR≤ 1.1:1Near-ideal input match
Output VSWR≤ 1.2:1Tolerant of load mismatch
Harmonic suppression≤ −65 dBcAt rated saturated output
Spurious suppression≤ −70 dBcFull band; space-grade EMI margin
Power-added efficiency, PAE≥ 38%25 °C, rated CW operation
AM-PM conversion≤ 2°Linear phase for digital carriers
Operating modeCW standard; pulse optionalHigh duty cycle supported
Impedance50 ΩStandard RF interface

Power, mechanical and environmental

ItemSpecification
DC supply+28 V nominal (24–32 V input range)
Maximum operating current≤ 14 A
Quiescent current≤ 2.8 A
CoolingForced air (standard) / liquid cooling (optional)
Operating temperature−40 °C to +65 °C
Storage temperature−45 °C to +85 °C
RF output interfaceWR-42 waveguide (standard) / 2.4 mm KF coax (optional)
Control interfaceDB9, RS-485 (standard) / RS-232 (optional)
Form factor19-inch rack, 2U
Weight≤ 6.2 kg

Protection and monitoring

  1. Over-temperature: linear power derating above 65 °C case temperature, automatic shutdown at 72 °C and recovery at 58 °C; all thresholds software-configurable.

  2. Over-current, under-voltage and over-voltage: nanosecond response, fault latching and stored fault codes.

  3. VSWR protection: software-set threshold; fast output cut-off on open, short or severe mismatch, protecting the final GaN die.

  4. Real-time telemetry over serial: output power, input power, case temperature, operating current, VSWR and fault codes.

  5. Status and alarms: local LED indication plus remote alarm reporting; multiple amplifiers can be networked and monitored as one group.

Customisation: liquid-cooled version, pulse mode, CAN bus, Ethernet remote control and custom power levels.

Specifications are typical and subject to change without notice. Please request the current datasheet before system design.

客服中心
联系方式
18688706870
0755-29210759
- 销售
微信18688706870
seo seo