扫码咨询

新闻动态

首页 >> 新闻动态 >> 100 MHz-6.5 GHz Wideband Sweep Source Module (1/2): 200 MHz Bandwidth, 500 kHz Step, +5 dBm
详细内容

100 MHz-6.5 GHz Wideband Sweep Source Module (1/2): 200 MHz Bandwidth, 500 kHz Step, +5 dBm

At a glance

ParameterValueComment
Frequency range100–6500 MHz65:1, approximately 6 octaves
Instantaneous bandwidth200 MHz maxCentre frequency and bandwidth configurable
Frequency step500 kHz12,800 points across the band
Scan rate500 kHz step rate, dwell down to 1 µsTable-driven, not command-driven
Output power> +5 dBm (spec) / ≥ +8 dBm (internal limit)Over full band, full temperature, 12 V worst case
Attenuation31.5 dB in 0.5 dB steps6-bit digital step attenuator
Supply12–28 V DC, ≤ 0.5 AStandby < 6 W
Temperature−40 °C to +70 °CFull-temperature data required, not typicals
Size / mass100 × 62 × 29 mm / 220 ± 10 gIncluding connectors
RF interfaceSMA female2.92 mm optional above 6.5 GHz
ControlRS-422, 5-wire, 115.2 kbpsCascade up to N units

1. The difficulty is the octave count, not the power

A 65:1 frequency span is where this design lives or dies. At 100 MHz the free-space wavelength is 3 m; at 6.5 GHz it is 46 mm. A 20 mm microstrip line is an ideal wire at the bottom of the band and a transmission line approaching 90° of electrical length at the top. A 100 pF capacitor behaves as a capacitor at 100 MHz, passes self-resonance around 2 GHz, and is an ill-defined short stub by 6.5 GHz.

Designers who apply narrowband habits to this problem get a predictable failure mode: gain stacked at the low end collapses at the high end; flatten the high end and the low end oscillates. Every adjustment trades one end of the band against the other.

The technical content of this module therefore reduces to one sentence: hold gain, flatness, output power, spurious content, DC power and volume simultaneously across a 65:1 span. The sections below follow the order in which those constraints have to be resolved — requirement decomposition first, architecture second, component selection third, matching and production last.

Device part numbers and parameters quoted here are taken from public datasheets and from measurements on previous programmes. Selection decisions should always be re-validated against the latest datasheet and against data measured on your own board.


2. Decomposing the requirement before drawing a schematic

2.1 Four tiers, not one list

The most common early mistake is to treat every line of the specification table as equally binding. In practice the requirements fall into four tiers, and the engineering effort has to be allocated accordingly.

TierContentConsequence of missing it
1. Hard limits100–6500 MHz; 12 V DC (28 V max); 0.5 A max; −40 to +70 °C; 100 × 62 × 29 mm; 220 ± 10 g; SMA; RS-422Cannot be negotiated. These define the mechanical and thermal envelope
2. Committed performance200 MHz max bandwidth; 500 kHz step; 31.5 dB attenuation; 0.5 dB step; > +5 dBm outputWritten into the technical agreement, verified point by point at acceptance, over temperature
3. Typical valuesStandby power < 6 W; input/output VSWR; phase noise; spurious rejectionQuoted as typical; internal margin retained
4. Targets+10 dBm output; ±1 dB flatnessStretch goals, never acceptance criteria

The value of the tiering shows up in design reviews: it makes visible which numbers can be traded and which cannot. The classic failure is spending tier-1 effort on a tier-4 target — doubling cost for a parameter nobody will measure.

2.2 Instantaneous or tunable? A three-fold cost difference

Before choosing devices, establish whether 100–6500 MHz means instantaneous coverage or tunable coverage. The two answers differ by roughly a factor of three in cost.

Instantaneous 6.4 GHz coverage forbids band segmentation in the RF path. It forces distributed amplifiers and broadband balun structures, and the noise figure, DC power and cost all suffer. Tunable coverage — only 200 MHz occupied at any instant — allows switched filter banks, band-split matching and band-split synthesis, which raises performance and lowers cost at the same time.

Roughly ninety percent of sweep-source and interference-simulation requirements are the tunable case: settable centre frequency, configurable bandwidth, 200 MHz maximum. Once that is settled the architecture follows: the RF chain is a single 100–6500 MHz through-path, and frequency selection is done in the LO and filter banks, not in the RF path.

2.3 The 500 kHz figure: do the arithmetic first

"500 kHz scan rate" is ambiguous. It normally means a 500 kHz step with configurable dwell, not 500,000 random-access hops per second. The arithmetic is worth doing explicitly.

At 500 kHz steps across 100–6500 MHz there are 12,800 points. With 1 µs dwell a full sweep takes 12.8 ms; at 20 µs dwell, 0.26 s. Trivial in principle.

The bottleneck is not PLL settling. It is the command interface. RS-422 at 115.2 kbps carries a set-frequency command of a dozen bytes in about 1 ms. If the host sends one command per point, the ceiling is roughly 1,000 hops per second — two and a half orders of magnitude short.

The architecture therefore has to be table-driven: the host writes a hop table, dwell time and loop mode into FPGA RAM once; the FPGA then sequences the LO, attenuator and filter channel locally. That imposes two hard requirements on the synthesiser: PLL lock within 20 µs (10 µs preferred), and spurious settling that is acceptable within a 1 µs dwell.

The digital side follows: 200 MHz instantaneous bandwidth needs at least 400 MSPS by Nyquist, so a 1 GSPS DAC with oversampling headroom. The DAC sample rate sets instantaneous bandwidth, not carrier frequency; translation to 100–6500 MHz is done by the upconversion LO. A 48-bit phase accumulator gives a frequency control word of about 1.41 × 10⁸ at 1 GSPS for a 500 kHz step, i.e. microhertz resolution — no post-tuning required.

2.4 The "+5 dBm" trap

+5 dBm looks like a single-stage amplifier job. Three budgets show why it is not.

Loss budget. A realistic accounting of the passive path: 0.2 dB per SMA (two), 0.3 dB for input limiting/ESD structure, 1.5–2.5 dB for the 6-bit DSA, 1.2 dB for two series switches, 2.5 dB for the worst filter segment, 0.3 dB for the coupler, 0.8 dB for microstrip and vias. Total 7–8 dB. If the final stage delivers +5 dBm, the port delivers −2 to −3 dBm.

Margin budget. The specification says "greater than +5 dBm, may vary with frequency". That sentence is both an allowance and a trap: acceptance is done point by point with a power meter. The internal control line should be +8 dBm at any frequency, in any 200 MHz sub-band, over −40 to +70 °C, at 12 V minimum input — a 3 dB margin, which is the normal RF convention.

Back-off budget. The final stage cannot run in compression; broadband noise modulation with a high peak-to-average ratio will clip and generate spurious products. With 6–8 dB of back-off, the final stage needs a P1dB of at least +18 to +20 dBm. Adding 7–8 dB of path loss, 8 dB of required output and 7 dB of back-off puts the target P1dB at +22 to +23 dBm.

The three budgets converge on a concrete choice: a broadband driver with P1dB of about +23 dBm (200 mW) as the final stage, preceded by a ~15 dB small-signal gain block, total gain around 30 dB, driven at roughly 0 dBm. That is the cheapest configuration that meets the number.

2.5 31.5 dB in 0.5 dB steps: selecting the DSA

0.5 dB steps over 31.5 dB is the standard 6-bit arrangement (0.5/1/2/4/8/16). Four criteria decide the part.

  1. Coverage down to 100 MHz. Many silicon DSAs only specify from several hundred MHz; loss and return loss change character at the low end.

  2. Accuracy over temperature and frequency. ±0.5 dB for the low bits, ±1.5 dB accumulated at the 16 dB bit. Ask for measured over-temperature data — datasheet typicals are not sufficient.

  3. Switching transient. Fast power switching in a sweep source requires settling under 1 µs. Many GaAs DSAs are slow here (hundreds of nanoseconds to microseconds); silicon parts are generally faster.

  4. Relative phase shift. Attenuation changes shift phase. Irrelevant for a single module, critical for cascaded or coherently combined systems.

Two Huashi parts illustrate the trade:


Part A (silicon)Part B (GaAs pHEMT)
Range0.1–6 GHz0.5–40 GHz
Insertion loss0.5 dB (0.1–2 GHz), 0.8 dB (2–4 GHz), 1.3 dB (4–6 GHz)5–6 dB
Accuracy±0.5 to ±1 dB±1 dB
Switching240 ns30 ns
Package / supply4 × 4 mm QFN24, 3 Vdie / package, negative rail typical

Note the loss slope of Part A: 0.5 dB at the bottom, 1.3 dB at the top — already 0.8 dB of negative slope that must be carried in the flatness budget. Part B buys bandwidth and switching speed with 4 dB more loss; whether that is acceptable depends on whether the constraint is bandwidth or power budget.

2.6 Thermal: from module power to junction temperature

12 V × 0.5 A = 6 W. That is the ceiling for the whole module at full load, and it is tighter than it looks.

A realistic breakdown: RF chain quiescent 1.5–2 W (final stage 12 V × 130 mA ≈ 1.6 W, pre-drivers 0.3 W), FPGA and configuration 0.8–1.2 W, DAC and clock 0.5–0.8 W, RS-422, bias and detection 0.2 W. Total 3–4.5 W — inside 6 W, but without much room. The trap is FPGA logic: a large device with a fast clock can pass 2 W on its own. A ~50k-LUT class device is sufficient and keeps both power and thermal design simple.

For spaceborne use the calculation has to go one level deeper. There is no convection in vacuum; heat leaves by conduction and radiation only. With a 25 °C/W junction-to-housing path, 1.6 W means a 40 °C rise; at a 70 °C housing limit the junction approaches 110 °C. GaAs pHEMT channels are rated to 150 °C, with long-term reliability normally derated to 120 °C. The final stage therefore needs a metal carrier (MoCu or CuMoCu) and a thickened base or an external thermal face. Carrying the budget through to junction temperature, rather than stopping at module power, is where the real margin is found.

2.7 The 220 g window

6061 aluminium at 2.7 g/cm³: a 100 × 62 × 29 mm housing with 1.5 mm walls and a 2 mm base is about 55 g. Three boards with components, about 80 g. Four SMA connectors at 8 g each, 32 g. DC and I/O connectors, 20 g. Shielding walls and standoffs, 20 g. That is just over 200 g, leaving roughly 20 g for potting, thermal pads and harness.

The rules that follow: do not thicken the walls; do not pot the whole cavity — pot only the PA and power sections; use lightweight stainless or beryllium-copper SMA bodies; machine the internal walls in one operation rather than assembling them from screws. Going further for space means aluminium-silicon or SiC carriers and pocketing — a different cost class.


3. Architecture

3.1 Five master schematics

Start with five: RF chain, power, bias and protection, monitoring and communication, digital/FPGA. Sub-sheets are named by function, location and revision (e.g. PA_DRV_U1A_V03). This is not bureaucracy — during production it is the only reliable way to trace a change back to a specific assembly.

3.2 Transmit chain order

SMA in → ESD/limiter → 6-bit DSA → switch → band-split pre-filter →gain block (15 dB) → inter-stage equaliser → driver → final PA →directional coupler → output filter → isolator/limiter → SMA out

The order is deliberate:

  • ESD protection first, because the input connector is what gets touched and what gets charged cables.

  • DSA before the gain stages, so it operates at low level, far from its 21 dBm input P1dB, and so large signals never reach it.

  • Filters before the gain stage, not after, so the filter does not have to handle power and its loss does not come straight out of the output budget. The low-band segments need care here: below 1 GHz a 2.5 dB filter is acceptable, whereas the segment near 6.5 GHz must stay under 1.5 dB.

3.3 Coupler and detector

A −20 dB coupler feeds a log detector for power monitoring and closed-loop levelling. Coupling too tightly breaks the detector's dynamic range: at −10 dB coupling and +8 dBm output the coupled port sees −2 dBm, fine; but at maximum attenuation the output falls to −23 dBm and the coupled port to −33 dBm, outside a 50 dB detector's usable span. At −20 dB coupling the coupled port sees −12 dBm at full power (mid-scale, where the log slope is most linear) and −43 dBm at minimum output — still inside 50 dB of range.

3.4 Why not a single conversion to 6.5 GHz

Single conversion is the obvious approach: 200 MHz IF, LO swept 100–6700 MHz, mix straight to RF. Three obstacles make it unattractive.

  1. LO coverage. Covering 100–6700 MHz continuously is a 65:1 span; a single PLL cannot do it, so the LO must be band-switched, and phase continuity and lock time at the switch points are poor.

  2. Image rejection. With a 200 MHz IF the image is only 400 MHz away. Near 6 GHz that requires a 6.7% relative-bandwidth filter, which is buildable, but the filter bank must switch with the LO — doubling control complexity.

  3. LO leakage and mixing spurs land in-band. This is the decisive objection for a sweep source.

The standard solution is dual conversion:

  • Stage 1: 1 GHz IF (from an 800–1200 MHz DAC output, or zero-IF I/Q modulation translated to 1 GHz) mixed with LO1 to a fixed high IF of 7.5 GHz. LO1 is fixed at 6.5 GHz or 8.5 GHz; high-side or low-side injection is chosen by which spur you fear more.

  • Stage 2: 7.5 GHz high IF mixed with LO2 (1.0–7.4 GHz) down to 100–6500 MHz. The image of this stage falls at 15 GHz minus the output frequency, at least 8.5 GHz away from the band, and is removed by a fixed 8 GHz low-pass filter that never switches. This is the real advantage of dual conversion: the variable part is pushed into the LO, and the fixed part is handled by a fixed filter.

LO2 still needs two segments — 1.0–3.7 GHz and 3.7–7.4 GHz — with a divide-by-two or VCO switch at the crossover. Huashi fractional-N synthesisers in the 0.2–24 GHz class cover this with margin: −233 dBc/Hz normalised in integer mode, −228 dBc/Hz in fractional mode, 200 MHz integer / 150 MHz fractional phase-detector frequency, 3.3 V, 4 × 4 mm QFN. A phase-detector frequency above 100 MHz supports lock times under 20 µs.

A caution on second-sourcing: substituting one synthesiser for another is not a package swap. Phase-noise curve, spur table, temperature drift and supply evidence have to be re-qualified. Any of the four missing means the substitution is not done.

3.5 Level plan, stage 2 upconversion

NodeLevelBasis
LO2 drive into mixer+7 dBmKeeps half-LO spurs down
7.5 GHz high IF into RF port−3 dBmBelow mixer input P1dB
Mixer output−12 dBm9 dB conversion loss
After fixed gain (+15, +12 dB)+15 dBm—
After equaliser and routing+13 dBm2 dB
At final stage input+6 dBmAfter switch, filter, coupler
Final stage output+18 dBm12 dB gain, ~5 dB below P1dB

This is the single-tone, full-scale condition. During actual sweeping the DSA removes 10–20 dB, the final stage input falls to −4…+6 dBm, back-off exceeds 10 dB and the output settles at +8 to +10 dBm — on the internal control line.

3.6 Spurious budget

Every mechanism needs an explicit line in the budget, otherwise the prototype spectrum is a field of grass with no way to trace it.

MechanismEstimateMitigation
LO leakage−23 dBm at mixer output, −43 dBm at port after 20 dB filtering (−51 dBc)Post-mixer switched high-pass if isolation is insufficient
IF leakage−25 dB RF-to-IF isolation, similar treatmentSame
Half-LO (n/2)Worst when LO drive is lowKeep LO drive at +7 dBm or above; do not economise on bias current
IM2 / IM3Two tones at −10 dBm each; products better than −50 dBcMixer IIP3 plus DSA operating point

客服中心
联系方式
18688706870
0755-29210759
- 销售
微信18688706870
seo seo