扫码咨询

新闻动态

首页 >> 新闻动态 >> 100 MHz-6.5 GHz Wideband Sweep Source Module (2/2): Components, Matching, Production
详细内容

100 MHz-6.5 GHz Wideband Sweep Source Module (2/2): Components, Matching, Production

Part 2 of 2. Part 1 covers why a 65:1 span is the hard part, how the requirement was decomposed, and the dual-conversion architecture.

4. Component selection

4.1 Final stage

Requirement: P1dB +22 to +23 dBm, gain ≥ 12 dB, 12 V single supply, 100–6500 MHz, efficiency as high as possible.

A 0.25 µm GaAs pHEMT driver in the GM1309 class meets the low band comfortably: 30–3000 MHz, +31 dBm saturated output, 17 dB gain at +30 dBm output, 50% PAE, 12 V single supply, 131 mA quiescent, 4 × 4 mm QFN, input return loss better than −15 dB, +22 dBm maximum input, −55 to +125 °C. Single supply, minimal external parts, good efficiency — the best cost-performance point in this design.

It stops at 3 GHz. Two options cover 3–6.5 GHz:

  • Band split with a switch. Below 3 GHz use the pHEMT device; 3–6.5 GHz use a driver rated above 6 GHz, each matched separately and combined through a switch. Cost: 1 dB of switch loss, one extra switch, one extra control bit.

  • One device covering the whole band. Cost: 3–5 percentage points of efficiency in the 1–3 GHz region.

Recommendation: band-split. The module already segments filtering and LO generation, so an extra switch path is not a system-level burden, and the efficiency is converted directly into thermal margin.

Scaling path, for when a customer asks for 10 W, 100 W or more: 30–2500 MHz / +40 dBm / 52% / 28 V and 30–2700 MHz / +37 dBm parts in the same family, then GaN — 20–3000 MHz, 28 V, 100 W, 19.5 dB gain, 70% efficiency, or internally matched broadband GaN modules.

4.2 Gain stage and LNA

A 20–6000 MHz GaAs pHEMT MMIC with 0.7 dB typical noise figure, +20 dBm output P1dB, 5 V single supply, 50 mA, internally matched to 50 Ω, available as die, SOT-89 and 2 × 2 mm LGA, serves two roles: the 15 dB transmit gain stage, and — in a dual-channel or receive-capable variant — the LNA.

Internal 50 Ω matching does not mean the layout is free. DC blocks at the input, decoupling placement and ground-plane integrity still decide whether it oscillates near 6.5 GHz. On three boards using this part, two showed a 3–4 dB gain peak near 5.8 GHz that was only removed by relocating the decoupling capacitors.

Selection criteria for the LNA class: in-band gain flatness (over temperature, not typical), P1dB (whether it can serve as a transmit pre-driver), and PSRR (DC/DC ripple modulates directly onto the RF).

4.3 Switches: pick two of three

Low insertion loss, high isolation, high power handling — choose two. Silicon switches give 0.5–0.8 dB loss, fast switching and low control levels, but limited power handling (P0.1dB typically +20 to +25 dBm); they belong in small-signal positions after the DSA and around the mixer. GaAs switches handle +30 dBm and isolate well, at 1–1.5 dB loss and with a negative or TTL-converted control; they belong at the output and in any T/R path.

A practical note on cascading: isolation does not simply add. With more than about 10 mm of line between two switch stages, radiation and coupling along that line typically cost 5–8 dB of measured isolation versus calculation. Place cascaded switches back-to-back, keep the interconnect under 3 mm and ground it on both sides.

4.4 Filter bank

Five segments: 100–500, 500–1500, 1500–3000, 3000–4500, 4500–6500 MHz.

The low segments have large relative bandwidth (5:1) — a cascade of lumped high-pass and low-pass sections is cheaper and smaller than a bandpass. The high segments are narrow in relative terms (1.4:1) — coupled-resonator or ceramic dielectric bandpass.

The hard rule: above 3 GHz, wire-wound inductors are past self-resonance; do not use lumped elements there. Use distributed structures — parallel-coupled lines, hairpin, interdigital — or ceramic dielectric filters.

Four numbers decide a filter: in-band loss, skirt steepness, stopband rejection, and group-delay variation. For a sweep source the last one matters most: group-delay variation sets pulse broadening and sweep transient tailing. For noise-modulated jamming waveforms it is critical — above about 5 ns of variation the noise bandwidth is visibly sculpted and the effectiveness drops.

Huashi supplies custom filter banks from its own thin-film and micro-assembly lines, which for small quantities and fast turnaround usually beats a large foundry's production queue.

4.5 DAC and clock

A 1 GSPS, 14-bit DAC is the baseline. Companion 16-bit 500 MSPS DAC and 16-bit 250 MSPS ADC devices from the same family keep the BOM single-sourced. A cheaper route is a 12-bit 2.5 GSPS part, at the cost of 60–65 dB SFDR — the spur floor then has to be corrected in the digital domain.

A more elegant option is a DAC with an integrated DDS: 1 GSPS, 14-bit, serial I/Q input, > 80 dBc narrowband SFDR. It removes the NCO from the FPGA, cutting both logic and power — attractive against a 6 W budget.

Channel count: 200 MHz instantaneous bandwidth as a single real signal fits one 1 GSPS DAC. For I/Q — required for single-sideband operation and image rejection — use two DACs or one dual-channel device.

The clock is the most expensive component and the one that cannot be economised. DAC clock phase noise sets output phase noise and the spurious floor. A 100 MHz TCXO (±0.5 ppm, −40 to +85 °C) as reference, multiplied to 1 GHz by a Huashi clock generator or PLL, gives integrated jitter in the 100 fs region.

Three traps:

  1. Routing. Differential, grounded on both sides, away from digital buses. Supply the DAC clock pins through a ferrite bead with a second-stage decoupler.

  2. Do not route the clock through the FPGA's internal PLL. The FPGA's internal PLL jitter is typically 20–50 ps worse than a dedicated clock generator, which destroys the ENOB of a 14-bit DAC.

  3. Reference supply. Use a low-noise LDO for the TCXO; never share the FPGA 1.0 V core rail.

4.6 FPGA

TierDevice classUse
Commercial / commercial space~50k LUT, 5 PLLs, 84 hard multipliers, DDR3-800, AES, free toolchainDDS, hop table, attenuation control, RS-422, detector sampling, temperature compensation — with more than half the resources left
Cost-critical~5–10k LUTDSA control, temperature sensing, RS-422; sufficient for many jamming-controller designs
High-reliability / space325k LUT, 840 DSP, 16.4 Mb BRAMAccepted across the aerospace ecosystem; radiation-tolerant variants available

Three FPGA pitfalls, all of them common:

  1. Toolchain. The Huashi toolchain is not the mainstream EDA flow. PLL, FIFO and DDR IP must be re-learned; budget two weeks.

  2. Internal PLL jitter, as above.

  3. Configuration flash. Huashi FPGAs with Huashi SPI flash: the boot-mode pins must be tied high or low per the datasheet, never left floating. A floating mode pin produces a board that simply will not boot, and it is usually found after a week of debugging.

4.7 Detection, monitoring and interface

A log detector with 50 dB of ±3 dB range (40 dB of ±1 dB), +10 dBm maximum input, 16–18 mV/dB slope, 3.3–5.5 V supply, 20 ns rise/fall and a temperature-compensation pin closes the levelling loop. With −20 dB coupling the detector sits mid-range at full power and at −43 dBm at minimum output — below the ±1 dB segment but inside ±3 dB. Closed-loop levelling depends on slope and repeatability; absolute accuracy comes from the factory calibration table, which is why the low-power end still holds.

RS-422, five wires (Y/Z out, B/A in, GND), through a Huashi transceiver. For cascading, the host connects to the first unit's RS-422-IN and each OUT feeds the next IN. Fit a 120 Ω termination footprint at every input; populate it only on the last unit. Without this, three or more cascaded units begin to error.

Alarm and enable lines (current, temperature, PA enable) are 0/3.3 V and connect directly to FPGA I/O — with a 100 Ω series resistor and 100 pF to ground on each, otherwise internal switching noise is injected straight into the digital ground. Two 0–3.3 V ADC inputs are enough for temperature, detected voltage and supply current; a small external multi-channel ADC keeps the DAC's digital resources free.

4.8 Power

12–28 V input, with 5 V and 3.3 V for the PA, DAC and clock, and 1.0 V core plus 1.8 V/3.3 V I/O for the FPGA. Two stages: a wide-input buck from 12–28 V to 5 V, then 5 V to 3.3/1.8/1.0 V. Wide-input bucks covering 4–36 V in and 2–3 A out are available from Huashi at roughly half the imported price.

Three cautions:

  1. Switching frequency. With a 100 MHz low band in the same housing, a 500 kHz–2 MHz switching regulator puts its harmonics across several hundred MHz. Choose ≥ 2 MHz switching and push the fundamental and low harmonics above 100 MHz, where filtering works.

  2. Layout. Input capacitors hard against VIN and GND, loop area minimised; shielded power inductors only — an unshielded drum inductor on an RF board is a broadcast antenna.

  3. Rail separation. Feed the PA, DAC and clock 5 V/3.3 V through ferrite beads from separate branches; never share the FPGA core rail.

Efficiency sets the standby figure. 90% at the first stage and 85% at the second gives about 76% overall: a 3.5 W load draws 4.6 W, i.e. 0.38 A at 12 V — inside 0.5 A. At 70% overall the same load needs 5 W and 0.42 A: still passing, with 0.08 A left. Every 5 percentage points of efficiency is a few hundred milliamps of margin.

4.9 Passives and connectors

At 6.5 GHz, boards fail on passives more often than on ICs.

Capacitors, three classes. RF coupling and matching: high-Q microwave porcelain, 0402, 0.3–100 pF, C0G/NPO, Q > 100 at 1 GHz. Huashi microwave porcelain series cost a third to a half of the established US parts and are adequate from 1 to 6 GHz. Mid-band and bias decoupling: X7R 0402/0603 — and remember the DC bias derating; a 100 nF 0603 at 5 V is effectively about 60 nF, so decouple against the real value. Bulk: tantalum or polymer, 10–100 µF.

Inductors: specify self-resonant frequency, not inductance. A 1 nH wire-wound part self-resonates at 6–10 GHz, 2.2 nH at 4–6 GHz, and anything above 4.7 nH is capacitive by 3 GHz. Above 4 GHz, replace lumped inductors with high-impedance line: a 0.25 mm × 3 mm trace is about 2 nH with no self-resonance and better unit-to-unit consistency.

Connectors. SMA is adequate to 6.5 GHz over this span, but use RF-grade parts — beryllium-copper gold-plated centre pin, PTFE dielectric — not the low-cost video-grade SMA, whose VSWR reaches 1.5 above 3 GHz. 2.92 mm is the option if the band is later extended. For DC and I/O, use microminiature rectangular connectors rather than pin headers; headers work loose under vibration.


5. Matching: measured comparison of three topologies

Three matching networks were built on the same device, in the same housing, with nothing else changed, and measured at seven frequencies. The absolute numbers are indicative; the trend is the point.

Topology100 MHz1 GHz3 GHz6.5 GHzFlatness
A. Three-section lumped LC ladder+9.2 dBm+10.1+9.6+5.1±2.6 dB
B. Lumped below 1.5 GHz, stepped-impedance plus open stub above+9.0+9.8+9.9+7.8±1.4 dB
C. Lumped low band, stepped mid band, Klopfenstein taper above 4 GHz, plus positive-slope equaliser+8.8+9.4+9.5+8.6±0.6 dB

Topology A collapses at the top of the band because the inductors are past self-resonance by 4 GHz and the network is no longer the network that was simulated. Topology C costs 0.4 dB of extra loss and 6 mm of board length, and buys ±0.6 dB flatness.

Production chose C. The 0.4 dB is recovered with 0.4 dB of front-end gain; the flatness saves the manual equalisation of every board on the line. That is the production trade: board area and a little gain, in exchange for test time.

5.1 Tuning procedure

  1. Measure the device, not the datasheet. Fit SMA launches at the input and output of the bare device on a characterisation board and measure S11/S22 at the seven points. This is the real starting impedance; the datasheet was measured on a different layout.

  2. Plot the trajectory on the Smith chart. If the locus runs along a constant-resistance circle, series inductance and shunt capacitance will pull it back to centre. If it circles the centre, multiple sections and damping are required. If low and high bands sit on opposite sides of the chart, the band must be split — which is the fundamental reason a 65:1 match cannot be done in one section.

  3. Tune from the bottom up. Optimise 100–500 MHz first, then add segments one at a time, re-checking the low band after each addition. Adding a high-band stub moves the low-band S11; that coupling is unavoidable and costs two or three iterations.

  4. Flatness last. Once VSWR is better than 2.0, flatten S21 with the equaliser and the attenuation code table. Always VSWR first, flatness second — the reverse order wastes the effort.

5.2 Three pitfalls that look correct

Pitfall 1 — too many sections in simulation. More sections mean wider theoretical bandwidth, but each carries loss and manufacturing tolerance. Above roughly ten sections, a real board is almost certain to measure worse than the simulation. Validate with Monte Carlo on component tolerance and on etch variation before committing.

Pitfall 2 — lumped elements above 4 GHz. The self-resonance table in §4.9 is not a guideline, it is a limit. A three-section lumped match that looks perfect at 2 GHz will show a 3 dB notch at 6 GHz because the series inductor has become a capacitor. Replace with high-impedance line and re-optimise; the layout is larger but repeatable.

Pitfall 3 — no de-embedding. The SMA launch, the transition via and the connector pin add 0.3–0.8 dB of loss and tens of degrees of phase at 6.5 GHz. If the fixture is not de-embedded, the matching network is optimised for the fixture rather than for the device, and every board built from that design inherits the error. Measure a through line of the same length, subtract it, and only then tune.


6. Build or buy

Two parts of this module are usually not worth building in-house at low volume.

The converter chain. Two mixers, two LOs, filters and amplifiers in a few tens of millimetres will absorb half the project's debugging time. Off-the-shelf up/downconverter modules with IF, RF, LO, DC and serial interfaces remove that work entirely. The dividing line: above roughly 1,000 units per year, or with unusual band and bandwidth requirements, build it; at a few hundred units with a schedule to hit, buy it and put the engineering into the PA and system integration.

The power stage. Below 10 W, building from discrete or MMIC devices gives the best cost and volume. At 50 W and above — particularly for space or wide temperature — buy an internally matched module or have it assembled as a SiP by Huashi, whose in-house thin-film and eutectic die-attach lines deliver with full-temperature data.

The principle: what you save is engineering hours, not component cost. A module costs more than its constituent ICs, but two months of debugging and one failed board spin buy several hundred of them.


7. Summary

Six decisions determine whether a 65:1 sweep source reaches production:

  1. Confirm tunable rather than instantaneous coverage before choosing any device.

  2. Move the scan sequencing into the FPGA; the serial bus will never be fast enough.

  3. Budget the output power through loss, margin and back-off to a P1dB requirement — not from the specification number directly.

  4. Convert twice, keep the high IF fixed, and put the variable part in the LO.

  5. Band-split the final stage and the matching network; there is no single-section 65:1 match.

  6. Carry the thermal budget to junction temperature and the mass budget to grams, at the concept stage, not at the design review.


About Huashi

Huashi Digital Technology (Shenzhen) Co., Ltd. designs and manufactures RF, microwave and satellite communication equipment, including the HS-PA series power amplifiers (300 MHz–6 GHz) and wideband converter modules (0.8–18 GHz). Modules are built on Huashi bills of material, with full-temperature test data, and can be supplied with space-grade screening and radiation documentation on request.

Contact

  • Web: nosatr.com

  • Email: szwisi2023@gmail.com

  • Tel: +86 186 8870 6870

Specifications in this note are design references. Final performance is confirmed by measurement on the delivered unit.

客服中心
联系方式
18688706870
0755-29210759
- 销售
微信18688706870
seo seo