扫码咨询

新闻动态

首页 >> 新闻动态 >> Part 1: Reading the Spec Sheet - What a 100 MHz-3 GHz, 200 MHz Broadband Source Really Demands
详细内容

Part 1: Reading the Spec Sheet - What a 100 MHz-3 GHz, 200 MHz Broadband Source Really Demands

时间:2026-11-11     【原创】

On a new colleague's very first day at work, I put an aluminum box on the desk — 95 × 55 × 22 mm, 220 grams — and told him: don't rush to open ADS yet. First tell me, out of these few lines of specifications — 100 to 3000 MHz, 200 MHz bandwidth, 500 kHz sweep, output greater than 5 dBm, 12 V at 0.5 A, −40 to +70 °C — which line is the most unforgiving?

He thought for a long while and said "power." I said no. The most unforgiving part is the seven characters "100 to 3000 MHz" — a 30:1 frequency ratio. In school, an amplifier with 10% bandwidth already counts as broadband, and at 20% you can publish a paper. What does a 30:1 span mean? It means the wavelength at the low end, 100 MHz, is 3 meters, while at the high end, 3000 MHz, it is 10 centimeters. The same microstrip line is "a piece of wire" at the low end, and already a transmission line at the high end. The same capacitor behaves as a capacitor at 100 MHz, but near 2.5 GHz it may already be past its self-resonance and turned into an inductor. If you attack it with narrowband thinking, the moment you pile up gain at the low end the high end collapses; when the high end goes flat, the low end oscillates — nothing you tune ever comes out right.

So all the technical content of this board condenses into one sentence: within a 30:1 bandwidth, hold gain, flatness, power, spurious emissions, and power consumption down all at the same time. Today I will walk you through this job from the day the requirement landed, step by step. Everywhere I go I will bring along specific domestic part numbers, specific values, and specific pitfalls. It doesn't matter if you can't remember it all — when you're laying out your own board later, dig this out and read it again.

One more thing to put up front: I will mention the company Huashi (Shenzhen Huashi Digital Technology Co., Ltd.) repeatedly in this article. This is not an advertisement. After a decade or more of component selection, the number of domestic suppliers who can follow a project all the way from chips to micro-assembly to modules and up to a complete satellite can be counted on one hand, and they are one of them. Their sales lead, Mr. Li, can be reached at 18688706870 — for samples, full-temperature data, or alternative proposals, going to him directly is much faster than filling out a form on the website. In every scenario below I will be specific about which requirement should be taken to him and what to ask for.

Chapter 1: Tear the Customer's Specifications Apart and Do the Math

1.1 Operating band 100–3000 MHz: first ask, "Is the full band used simultaneously, or in segments?"

The first thing to do with the band spec is not to pick transistors — it is to go ask the application team: is this 100–3000 MHz an instantaneous bandwidth or a tunable bandwidth? These two phrases differ by one word, but the architectures they imply differ in cost by a factor of three. If the requirement is to cover 2.9 GHz instantaneously, then the front end basically cannot be segmented; you must go to a distributed-amplifier, wideband balanced architecture, and neither noise figure nor power consumption will look good. If it is tunable — only 200 MHz used at any instant — then you can use switches to select a filter bank and do segmented matching; the performance moves up a whole class and the cost comes down.

The vast majority of sweep-source and jammer requirements are "center frequency settable, bandwidth configurable, up to 200 MHz maximum" — that is, 200 MHz instantaneous, tunable across the whole band. Once this understanding is fixed, the architecture becomes clear: the RF chain is a full-wideband, DC-to-3000-MHz-through passband, and frequency selection is done by the local oscillator working with the filter bank — not by narrowband filtering on the main RF path.

1.2 Maximum bandwidth 200 MHz and maximum sweep rate 500 kHz: these two numbers are the exam paper for the baseband and the DAC

For 200 MHz of instantaneous bandwidth, Nyquist says 400 MS/s sampling is the floor; with engineering oversampling and a little margin, a DAC in the 500 MSPS to 1 GSPS class is the right pick. One concept must be made clear here: the DAC sample rate determines the instantaneous bandwidth you can produce, not the carrier frequency. Getting the signal up to 100–3000 MHz relies on the mixing LO that follows. In the domestic-parts arena at this tier, the DA1000 (14-bit, 1 GSPS, benchmarked against ADI's AD9144 family) is the first choice; if you need to save cost, you can start with a 12-bit, 2.5 GSPS domestic DAC, at the price of an SFDR of only 60–65 dB, which means you have to calibrate the spurious floor yourself in the digital domain. One more easily overlooked point: at 1 GSPS the DAC's data interface is DDR (double data rate), so on the FPGA side you must use ODDR primitives — or move to a JESD204B interface (in which case you add a domestic JESD clock chip, such as Huashi's clock devices). Do not assemble ordinary registers by hand; the timing will never close.

As for the 500 kHz sweep rate — does it mean 500,000 frequency hops per second, or a 500 kHz step? Confirm with the application team; it is usually the latter — a 500 kHz step with configurable dwell time. First do the arithmetic: from 100 to 3000 MHz in 500 kHz steps is 5,800 points; at 1 µs per point, one full sweep takes only 5.8 ms; even at 20 µs per point, one sweep is 0.12 s. So the real bottleneck was never PLL lock time — it is the command interface: over RS-422 at 115200 baud, transmitting a single set-frequency command takes several hundred microseconds. If you truly want hundreds of thousands of hops per second, the FPGA must run the hopping table by itself, with the PC only downloading the table. The design should achieve: PLL lock time under 20 µs (10 µs is better), dwell time configurable down to 1 µs; the DDS phase accumulator at 48 bits — a 500 kHz step at 1 GSPS corresponds to a frequency tuning word of 500k × 2^48 / 1G ≈ 1.41 × 10^8, giving step resolution at the microhertz level. That settles it once and for all.

1.3 Output power greater than 5 dBm: don't be fooled by this "small power"

Seeing "greater than 5 dBm," a newcomer's first reaction is "that's easy — one amplifier and done." I make him work through three accounts, and after that he never says it again.

First account: link losses. The module has a 31.5 dB digital step attenuator, a filter bank, switches, couplers, PCB traces, and SMA connectors — all of them eat power. From experience, here is a typical set of values: input and output SMAs, 0.2 dB each; one limiter or ESD structure on the board, 0.3 dB; the digital attenuator's insertion loss, 1.5–2.5 dB (a 6-bit attenuator with 0.5 dB steps and 31.5 dB range always lands in this range); two switches in series, 1.2 dB; the worst segment of the filter bank, 2.5 dB; splitter/coupler, 0.3 dB; microstrip plus vias, 0.8 dB. The total comes to roughly 7–8 dB. In other words, if the final PA only puts out 5 dBm, the port is left with −2 to −3 dBm.

Second account: margin. The customer wrote "greater than 5 dBm," with a footnote: "may vary across frequencies." That sentence is both a door left open for us and a hole dug for us: the open door means the whole band need not be identical everywhere; the hole means that at acceptance they will test point by point with a table, and you must pass everywhere. My internal control line is: at any frequency in the band, in any 200 MHz sub-band, across the full −40 to +70 °C range, at the lowest 12 V supply, the output shall be no less than 8 dBm. Keep 3 dB of margin — that is RF discipline.

Third account: compression. The final stage must not run in saturation; otherwise, once wideband noise rides up on it and the peak-to-average ratio climbs, the peaks clip and the spurious content explodes. We run the final stage backed off 6–8 dB, which means the final stage's P1dB must be at least 18–20 dBm. With 7–8 dB of link loss, plus 8 dB of output, plus 7 dB of back-off, a final-stage P1dB of 22–23 dBm is the comfortable landing spot — that is the real power requirement hiding behind "5 dBm output."

Once these three accounts are done, the scheme falls out: the final stage is a wideband driver amplifier with P1dB around 23 dBm (about 200 mW), preceded by a small-signal gain stage of about 15 dB, for 30 dB total gain, with input drive at the 0 dBm level. This is the cheapest way to do it.

1.4 Attenuation range 31.5 dB in 0.5 dB steps: how to choose a 6-bit digital step attenuator

A 0.5 dB step over a 31.5 dB range is the standard 6-bit set (0.5, 1, 2, 4, 8, 16 dB). Selection comes down to four things. First, the frequency coverage must include the 100 MHz low end — many silicon (SPA) attenuators only go down to a few hundred MHz, and their low-end insertion loss and VSWR change character. Second, attenuation accuracy: across temperature and frequency we must hold error within ±0.5 dB (low bits) to ±1.5 dB (cumulative at the 16 dB bit); for this you must demand full-temperature data from the vendor — datasheet typical values don't count. Third, switching transient: the sweep source must do fast power switching, so the switching time must be under 1 µs. Fourth, relative phase shift: the phase jumps when the attenuator changes state; in phased arrays or coherent-combining applications this can be fatal. A single module can skip it, but for cascading multiple units you must measure it.

In the domestic arena at this tier, I would look first at Huashi's GaAs digital attenuator chipsets, then at the 6-bit attenuator die from Yaguang Technology (Micro-star) — they carry 400+ models and 200+ shelf products covering attenuators, phase shifters, mixers and more, with frequencies up past 40 GHz and shorter lead times than the institutes. For more cost-driven civilian projects, look at RF-front-end vendors such as Chengdu Zengyi or Zhejiang Chicheng, where cost can be cut in half — but always demand the S-parameters at the 100 MHz point first. That is the easiest frequency to get burned on.

1.5 Supply DC 12–28 V, max 0.5 A @ 12 V: the 6-watt budget, counted cent by cent

The interface definition says DC-IN 12 V, while the spec table says 12–28 V. There is no contradiction — it is a wide-input supply. What really binds us is "max 0.5 A @ 12 V, standby below 6 W." Twelve volts times 0.5 A is 6 W: at full-power transmission the whole unit may not exceed 6 W.

Break the 6 W down: the RF chain — final stage at 23 dBm ≈ 200 mW output, at PAE 30%, is about 0.7 W DC; the driver stage, equalizer, attenuator, and switches add 0.3 W; LNA and detector, 0.1 W. The FPGA + DAC + clock: a domestic 28 nm small-logic FPGA such as Unisoc-logic's Logos-2 family, PGL22G or PGL50H class, running clocks under 100 MHz, draws roughly 0.5–1 W core plus auxiliaries; the DAC 0.2–0.3 W; the crystal oscillator and clock buffers 0.15 W. RS-422 transceivers plus LDO dropout losses, 0.3 W. The big items total 2.5–3 W, leaving 3 W for digital peaks and thermal margin. The budget closes — on the condition of efficiency. Iron rule: on the 12 V to 5 V / 3.3 V / 1.8 V / 1.0 V rails, do not use LDOs everywhere. The 12-to-5 V step must be a synchronous buck at 92% efficiency or better; the RF supply rails below 5 V can be washed once more through an LDO — there you are buying noise, not efficiency. If you drop 12 V straight to 1.0 V through an LDO for the FPGA core, 0.5 A burns 5.5 W and the budget blows up on the spot. That is the most common newcomer mistake I have seen.

1.6 Operating temperature −40 to +70 °C: this is the top of the commercial grade, not mil-spec

Do not reach for space-grade parts the moment you see −40 to +70. That is burning money for fun. Industrial-grade components cover this temperature range completely — but two places must still be handled across the full temperature range. First, the crystal oscillator: a TCXO with ±0.5 ppm drift is ±1500 Hz of carrier error at a 3 GHz carrier — visible when doing narrowband fine sweeps or long-dwell observation. If you need tighter, go to an OCXO (0.1 ppb class), at the cost of about 1 W of power that must be carved out of the 6 W budget. Second, amplifier gain drift: GaAs amplifiers run about −0.01 to −0.02 dB/°C, which across 110 degrees is 1–2 dB; without compensation, flatness is ruined. The compensation method comes later. For now remember one line: do temperature compensation in the digital domain — look-up tables plus DAC control of a VGA and the attenuator. Do not try to build an analog compensation network out of thermistors; over a 30:1 bandwidth you cannot build it.

1.7 Standby power under 6 W, weight 220 ± 10 g, dimensions 95 × 55 × 22 mm

Standby and transmit share the same 6 W ceiling, which means the digital section cannot slack off in standby: the FPGA goes to sleep, the DAC enters power-down mode, and the RF amplifier stages are switched off through their enable pins. The approach: in standby, keep only the 3.3 V always-on rail for the FPGA standby domain and the RS-422 transceivers; when a wake-up command arrives, bring up the RF rails, with the whole wake-up sequence done within 50 ms.

The 220 ± 10 g weight allowance is tight. With 6061 aluminum at 2.7 g/cm³, the 95 × 55 × 22 enclosure (1.5 mm walls, 2 mm base) is about 35 g; three boards with components, about 60 g; four SMAs at 8 g each plus the DC jack and I/O connectors, 15 g; shield walls and standoffs, 15 g. The total is about 150 g, leaving only 60 g for potting, thermal pads, and cabling. That is the height of the ceiling — so don't thicken the enclosure walls, and don't do a full-face potting job; only pot the PA and power sections. If this ever flies on a satellite and needs further cuts, you go to aluminum-silicon or silicon-carbide carriers and hollow-out lightening — Huashi routinely uses exactly these methods for spaceborne modules; ask Mr. Li (18688706870) and he can provide lightweight-structure case studies.

On dimensions, one remark: on the 95 × 55 mm board face, after deducting screw bosses and SMA footprints around the perimeter, the real area available for RF routing is about 85 × 45 mm. Into an area that small you must fit the RF chain, PLL, clock, DAC, FPGA, and power — dual channel — on a two- or four-layer board. This is the tightest constraint of the entire project, far tighter than the power spec. So my first reaction was: this cannot be one board forced to fit — it must be split.

Next in this series: Part 2 - Architecture: three roads to a 30:1 bandwidth signal source, and the one we chose.

客服中心
联系方式
18688706870
0755-29210759
- 销售
微信18688706870
seo seo