扫码咨询

新闻动态

首页 >> 新闻动态 >> Part 3: Component Selection - PAs, LNAs, Filter Banks, FPGA, DAC and PLL for a 100 MHz-3 GHz Source
详细内容

Part 3: Component Selection - PAs, LNAs, Filter Banks, FPGA, DAC and PLL for a 100 MHz-3 GHz Source

时间:2026-11-11     【原创】

This is Part 3 of a four-part series on designing a 100 MHz–3 GHz broadband frequency source module. Parts 1-2 covered the specifications and the architecture.

Chapter 3: Core Component Selection — One Part at a Time, with Part Numbers and Pitfalls

3.1 The power amplifier: small power, but the selection logic is identical to a 100 W PA

First, a matter of mindset: don't grab just any Gain Block because you only need 5 dBm. The selection logic for a power amplifier is the same whether it is 5 dBm or as much as 100 W: first the in-band gain and gain slope, then P1dB and linearity after back-off, then PAE and thermals, then stability, and finally consistency and procureability. Let me walk through this logic on a low-power example — later, when you build tens or hundreds of watts, copy it verbatim.

For the final stage I chose a medium-power wideband GaAs or GaN driver-type PA with these requirements: 100–3000 MHz, small-signal gain 15–20 dB, P1dB not below 23 dBm, OIP3 not below 35 dBm, in-band gain ripple within ±1.5 dB (flattened by an external equalizer), single 5 V / 8 V supply, current under 150 mA (under 1 W at 5 V — fits the power budget). There are quite a few domestic options at this tier: Sichuan Yifeng, Beijing Huixin Tong, Borui Jixin, Yaguang Technology, and CETC 13th Institute all offer wideband PA die in the 0.1–3 GHz, sub-1-watt class. Huixin Tong's HXTA3036T89 — a 0.01–3 GHz wideband part with 20 dB gain, P1dB 18.5 dBm, OIP3 32 dBm, 5 V at 50 mA — is well suited for the front-end stage; for the final stage, move up to a 0.1–3 GHz, 1-watt-class GaN or GaAs part.

If the customer later raises the power spec from 5 dBm to 30-40 dBm — common in jammer applications — go look at Ruichuang Microwave's D110X series: the D1102 is 0.03–3.2 GHz, 10 W, 28 V, gain 9–13.7 dB, Psat 40.8 dBm, efficiency above 52.5%, internally matched at the input, plastic DFN package, usable directly; the D1103 for 15 W, and the D1105 (0.01–1.2 GHz, 10 W, 59% efficiency) for higher efficiency below 1.2 GHz. For the 100 W class, look at Xinbaité's CBNTL100 (20–3000 MHz, 28 V, 100 W, gain 19.5 dB, 70% efficiency) or Borui Jixin's internally matched wideband GaN. Keep these on file — when the customer raises the power, you won't have to relearn anything.

Huashi's path on chips is a bit different: they own three process platforms — GaAs, GaN, and InP — with self-developed GaN HEMT power density reaching 6 W/mm, covering 0.1 to 100 GHz, plus their F-RISE packaging platform and a 3,000 m² packaging and micro-assembly line of their own. What does that mean? If the shelf die you can buy has an in-band slope you don't like, or you need it packaged with your own pinout definition, you can go straight to Mr. Li (18688706870) to discuss custom or semi-custom: die, carrier, wire bonding, and housing assembled into a module for you, delivered together with full-temperature S-parameters and power sweep data. Shelf civilian chips solve "available"; this kind of collaboration solves "good" and "stable." On major programs — satellites, airborne platforms — only the latter holds up.

3.2 The LNA: why does a transmit source need one?

Someone will ask: this is a transmit source — what do we need an LNA for? Two uses. First, the detector branch: the coupled signal is only about −10 dBm, and before it goes into the detector and ADC for power closed-loop control, an LNA in front lifts the dynamic range and resolution so that power readings hold ±0.5 dB. Second, future transceiver variants: this module can easily be turned into a transceiver; then the receive path needs an LNA, and selecting it once now means no board respin later.

Domestic LNAs at 0.1–3 GHz are the most mature category in domestic RF: many models, low prices, good specs. A 0.1–3 GHz part with 21.5 dB gain, 1.0 dB noise figure, P1dB 15 dBm, 5 V at 23 mA in a 2 × 2 mm plastic package; for higher gain, a 0.1–3.5 GHz part with 29.5 dB gain, 0.9 dB noise figure, P1dB 19 dBm; for spaceborne or harsh environments, the ceramic-packaged YLN109-0004A2C — 0.1–3.5 GHz, 31.5 dB gain, 0.7 dB noise figure. Parts in the 0.01–3 GHz class with 1.0–1.2 dB noise figure, P1dB 18.5 dBm, and OIP3 32 dBm are also very usable. And there are wideband LNAs — that 1 MHz-to-4 GHz part with 2.0 dB noise figure at 2 GHz, OIP3 21.9 dBm, 3.3 V at 37 mA, on-chip bias — whose external circuitry is the simplest of all.

Again: this module is a transmit source and the main chain needs no LNA. I include it for two reasons. One, the coupled detector branch: with 16 dB of coupling after the final stage, the coupled port sits at −23 to −13 dBm. The log detector's input floor is around −50 dBm — apparently enough, but add the detector front-end limiter loss of 1 dB, trace loss of 0.5 dB, and a 6 dB accuracy degradation at the low-power end, and the loop starts jittering at low power settings. So put a 15–20 dB LNA after the coupled port to lift the whole detection range — then the loop is stable. Two, receive derivatives: the same board, slightly modified, becomes a receive exciter or reconnaissance front end — and then the LNA is the main chain's first stage, and its noise figure directly sets system sensitivity.

Selection looks at four things: noise figure, gain, in-band flatness, OIP3. For 0.1–3 GHz with 1.5–2 dB noise figure, 20 dB gain, and OIP3 above 20 dBm, Huashi's shelf has plenty. A 0.1–6 GHz part (noise figure ~1.5 dB, gain ~20 dB), a low-band part (noise figure under 1 dB, gain above 30 dB), and an 8 V, 120 mA part (P1dB 26 dBm, suited for a high-linearity front end) — all of these wideband LNA die work.

Three pitfalls. First: the LNA fears mismatch above all; the moment the input VSWR degrades, the noise figure turns ugly — so tune the input for minimum noise matching, not for 50 Ω; the two often differ by a few tenths of a dB of gain. Second: there must be limiting or switching protection in front of the LNA — your board's output end doesn't fear incoming signals, but the coupled port and test ports will get mis-connected. Third: the LNA's out-of-band gain will amplify big low-frequency signals and compress the following stage — the gain above 3 GHz must be held down; ideally put a highpass section between stages.

For LNA selection watch three numbers: noise figure, P1dB (or IIP3), and in-band gain roll-off. At 0.1–3 GHz, wideband LNA gain typically drops 2–3 dB at the high end (set jointly by device fT and the matching network), while at the low end gain bulges easily because the bias inductance self-resonates. That bulge is the precursor of self-oscillation; later in the matching chapter I will show how to flatten it with resistive feedback.

3.3 The filter bank: segmentation, switching, three bands

The frequency planning fixed three segments: 100–500, 500–1500, and 1500–3000 MHz. These three are built differently. LTCC filter devices are mature in this range: small, temperature-stable, insertion loss 1.5–2.5 dB, more than 45 dB rejection below 1 GHz out of band. But LTCC has one unavoidable trap: its out-of-band rejection relies on in-package parasitic notches, which drift by tens of MHz between lots — so demand measured S2P files from at least three production lots, and use the worst curve for the system spurious budget; never use the datasheet's typical curve. Also, LTCC is multilayer ceramic and its pads are the RF ports: follow the vendor's reflow profile exactly — a ramp above 3 °C/s will crack it — and never put vias in the pads or run heat-spreading copper under them. That is the most common volume-production assembly-line mistake.

For 100–500 MHz, lumped LC is the best fit: a 5th- to 7th-order elliptic or Chebyshev, with Sunlord wirewound or multilayer high-frequency inductors (Q above 40) and capacitors. The key in this band is the low end: at 100 MHz an inductor's impedance is only about j60 Ω and a 100 pF capacitor is j16 Ω — component values are large, parasitics matter less, and it's easy; the hard part is high-end rejection — holding 40 dB above 1 GHz takes two extra notches. For 500–1500 MHz, use distributed elements: a coupled-line or hairpin bandpass on Rogers 4350B (εr 3.48, loss tangent 0.0037), three to four sections, insertion loss held within 1.2 dB, with more than 35 dB rejection above 2 GHz.

What about switches? For 0.1–3 GHz with insertion loss under 1 dB, isolation above 30 dB, and P1dB above 25 dBm, domestic GaAs SP3T parts or combinations of SPDTs all work — GaAs switch chips are cheap in volume. For more cost-driven civilian projects, SiGe or SOI switches are usable too, but watch their voltage handling and P1dB: SOI switch P1dB is generally only in the low 20s. Placed at a low-power point — after the attenuator, before the final stage — fine; placed after the final stage, it will burn.

3.4 The core FPGA: control, DDS, predistortion — one chip does it all

The FPGA on this board must do: a 48-bit DDS phase accumulator; IQ data shaping for the 200 MHz bandwidth (noise or sweep waveforms); parallel control of the 31.5 dB attenuator; DAC control of the VGA; reading the detector ADC and closing the power loop; SPI configuration of the PLL; the RS-422 UART and cascade repeating; and temperature-compensation table lookups. The logic volume is not large, but you need enough multipliers — a 200 MHz FIR for predistortion or pulse shaping takes a few dozen DSP blocks.

Three tiers of selection, by project grade. For civilian and commercial aerospace: about 50k LUTs, industrial −40 to 100 °C, free PDS toolchain, BGA256 package, friendly price; step up to the PGL100H if predistortion logic overflows. For demanding spaceborne applications: the 326k-LUT part with 840 DSPs and 16.4 Mb of BRAM, with the highest acceptance in military-aerospace programs; Huashi's spaceborne products use exactly these high-reliability FPGAs, and radiation-tolerant variants can be selected — for configuration details go to Mr. Li (18688706870), who can provide irradiation and temperature-lot data. For projects squeezed to the last cent: a small-logic device is enough for everything except the main datapath (I2C to control a DAC, read an NTC); many counter-drone projects get by with one small FPGA plus one DAC for temperature compensation.

Three pitfalls of FPGA selection, stated in advance. One: the development tools — the syntax and IP cores differ from Vivado; the PLL, FIFO, and DDR IP all have to be relearned; reserve two weeks. Two: domestic FPGAs' PLL jitter is 20–50 ps worse than the equivalent Xilinx part — so the DAC's clock must go from the external oscillator through the clock chip straight to the DAC, never out through the FPGA's internal PLL. Three: the configuration chip — for a domestic FPGA's SPI Flash, the boot-mode pins must be pulled up or down per the manual; never leave them floating.

3.5 DAC and clock: the source of all spurs

Choose a 14-bit, 1 GSPS-class DAC; or a DDS-integrated DAC (on-chip 1 GSPS 14-bit DAC plus DDS, serial IQ input, narrowband SFDR above 80 dB), which eliminates the NCO in the FPGA and cuts both logic volume and power. If money is short, go 12-bit — but a 12-bit SFDR is about 60–65 dB: enough for a jammer, not enough for an instrument-grade source.

The clock is the most expensive part in this module, and the one you may not economize on. The DAC's sample-clock phase noise directly sets the output's phase noise and spurious floor. Use a 100 MHz TCXO (±0.5 ppm, −40 to 85 °C) as reference, into a domestic clock chip or PLL (Chengdu Huawei's clock drivers, or the 13th Institute's clock devices) to multiply up to 1 GHz with jitter in the 100 fs class. The oscillator's supply must have its own dedicated LDO; its routing stays at least 5 mm from the FPGA and any DC-DC, over a complete ground plane, with absolutely no signal line passing under the crystal — I will yell about this again in the layout chapter.

3.6 PLL, VCO, and LO: the trade between hop speed and phase noise

The LO must hop between 1.1 and 4.4 GHz and lock within 10 µs. The approach: a wideband fractional-N PLL plus a wideband VCO, or a single integrated-VCO wideband PLL. A part with 8 GHz max input and a normalized noise floor of −227 dBc/Hz, paired with a suitable VCO, is a proven combination; integrated solutions also exist (from the former 24th Institute lineage and other frequency-source chips). Three cautions. One: fractional-N spurs — the ΣΔ modulator's spurs can land in-band, so either pick a part with spur cancellation or suppress them in the loop filter. Two: loop bandwidth — we want 10 µs lock, which needs a loop bandwidth above 100 kHz, but opened wide, the VCO's phase noise escapes; compromise at 50–80 kHz for a lock time around 15 µs, which is enough. Three: align the VCO's tuning voltage range with the PLL's charge-pump output (usually 0.5–4.5 V); if they don't align, add an op-amp level shifter — don't force it.

3.7 Detection, ADC, and supply monitoring

For power detection use a domestic log or RMS detector in the 0.1–3 GHz class with 40 dB dynamic range and ±1 dB accuracy — Huashi's shelf covers it. Behind it, a 12-bit ADC — a domestic SAR ADC at 1 MSPS or better — feeds the FPGA for the power loop. Temperature comes from an NTC or a digital temperature sensor; current from a sense resistor plus a zero-drift op-amp. The I_ALARM and T_ALARM outputs are 3.3 V logic from FPGA GPIOs through a driver; remember the 22 Ω series resistors and TVS diodes — once the interface cable gets long, ESD and surge come in right here.

3.8 Passives and connectors: the cheapest parts, the easiest to cause trouble

Capacitors: C0G/NP0 only. Never use X7R or Y5V in matching arms — X7R can lose more than 30% of its capacitance with voltage, temperature, and frequency; your match looks fine at room temperature and detunes when hot. A 0402 100 pF C0G self-resonates around 1.5–2 GHz; at 3 GHz it is already an inductor. So near 3 GHz, bypass with 10 pF and 100 pF in parallel to stagger the self-resonances. Inductors: Sunlord multilayer high-frequency or wirewound types — but read the Q at the datasheet's test frequency: many vendors specify Q measured at 100 MHz; used at 2 GHz, the real Q may be only a third of it.

Board-to-board and external connections: RF on SMA — pick the "removable stainless steel, 500 mating cycles" grade, not the few-mao brass gold-plated kind, whose VSWR degrades after three matings. The DC jack should be a threaded locking aviation connector or a 2.54 mm dual-row header with latch; I/O-CTRL on 2.0 / 2.54 mm socket strips. RS-422 transceivers: an isolated, 20 Mbps, wide-body SOIC16, −40 to 125 °C part or its equivalent — long cascade lines must be isolated; ground potential differences will kill non-isolated transceivers.

Next in this series: Part 4 - wideband matching, the real craft of this board.

客服中心
联系方式
18688706870
0755-29210759
- 销售
微信18688706870
seo seo