扫码咨询

新闻动态

首页 >> 新闻动态 >> HS-G01 0.3-18 GHz Four-Channel Downconverter - Full Specifications | Huashi Digital Tech
详细内容

HS-G01 0.3-18 GHz Four-Channel Downconverter - Full Specifications | Huashi Digital Tech

HS-G01 is a 0.3-18 GHz four-channel wideband downconverter manufactured by Shenzhen Huashi Digital Technology Co., Ltd. (Huashi Digital Tech). It converts four independent 0.3-18 GHz RF inputs to 1.3-2.3 GHz IF outputs with 1 GHz instantaneous bandwidth, at least 40 dB gain and 10 MHz frequency step, controlled over a 5 MHz SPI bus. It is one of four models in the Huashi HS-G Series wideband frequency converters.

What Is the HS-G01 and What Does It Do?

The HS-G01 (full part number HS-G4DF-RF0.3-18-IF1.8-BW1G) integrates an LO source, four independent downconversion channels, a 100 MHz reference clock and a power/control board. The four channels share one LO source but have independent digitally controlled RF and IF attenuation, which makes the module suitable for multi-channel reconnaissance, direction finding and coherent receiver arrays. An SPI bus sets the frequency and attenuation for each channel.

Key Facts at a Glance

AttributeValue
Model / short codeHS-G01
Full part numberHS-G4DF-RF0.3-18-IF1.8-BW1G
ManufacturerShenzhen Huashi Digital Technology Co., Ltd. (Huashi Digital Tech), www.nosatr.com
Function4-channel wideband downconverter
RF input frequency0.3-18 GHz
IF output frequency1.3-2.3 GHz
Instantaneous bandwidth1 GHz
Gainat least 40 dB
Noise figureno more than 8 dB
Frequency step10 MHz
Control interfaceSPI, 5 MHz clock, 8-bit address plus 16-bit data
Supply+12 V, 2.4 A typical
RF / IF connectorsSMP (4 x RFin, 4 x IFout)
Outlineapprox. 137 x 92 x 14 mm

Full Electrical Specifications

ParameterSpecification
RF input frequency0.3-18 GHz
IF output frequency1.3-2.3 GHz
Instantaneous bandwidth1 GHz
Gainat least 40 dB
In-band flatnesswithin +/- 3 dB
Maximum input power before damage2 W CW
Noise figureno more than 8 dB
Frequency step10 MHz
RF attenuation1 / 2 / 4 / 8 / 16 dB steps (digital code 1-31 dB)
IF attenuation1 / 2 / 4 / 8 / 16 dB steps (digital code 1-31 dB)
Linear output P-1at least 10 dBm
Intermodulation and spurious rejectionat least 50 dBc at Pin = -40 dBm
IF out-of-band rejectionat least 50 dBc at 1.8 +/- 0.7 GHz
Harmonic rejection-50 dBc or better
Test conditionsVcc = +12 V, I = 2.4 A, Pin = -40 dBm, 25 C

RF Ports, Power and Control Pins

RF ports: RFin1 to RFin4 (SMP, 0.3-18 GHz) and IFout1 to IFout4 (SMP, 1.3-2.3 GHz). Power: +12 V via a single feedthrough pin, GND via a grounding stud. Control: single-row 5-pin header - pin 1 MOSI, pin 2 MISO, pin 3 SCK (5 MHz), pin 4 CSB, pin 5 GND (digital ground).

SPI Register Map

RegisterWidthFunctionDescription
0x0016 bit [15:0]Frequency control wordRF = code[15:0] x 10 MHz; code range 200-1800
0x0116 bit [15:0]Channel 1 attenuationD[7:0] IF attenuation 1-31 dB; D[15:8] RF attenuation 1-31 dB
0x0216 bit [15:0]Channel 2 attenuationSame as 0x01
0x0316 bit [15:0]Channel 3 attenuationSame as 0x01
0x0416 bit [15:0]Channel 4 attenuationSame as 0x01

SPI framing: data is valid while SLE is low; the device samples SDA on the rising edge of SCK. One transaction carries an 8-bit address A and 16-bit data D. A[7] is the read/write bit (0 = write); A[6:0] addresses 128 registers.

Mechanical Dimensions

Approx. 137 x 92 x 14 mm shielded housing with 8 SMP ports (4 inputs, 4 outputs). Dimensions are reference values for the standard build; final tolerances, mounting holes and connector locations are defined in the official Huashi outline drawing and can be customized.

Typical Applications

  • Multi-channel wideband reconnaissance and direction-finding receivers in the 0.3-18 GHz band.
  • Coherent array receiver front ends where four channels share one LO source.
  • Airborne, shipborne and ground microwave ATE and receiver sensitivity verification.
  • Active radar jamming systems requiring four independent receive downconversion chains.

Frequently Asked Questions

Q: What is the HS-G01?
A: A four-channel 0.3-18 GHz wideband downconverter from Huashi Digital Tech, converting RF to 1.3-2.3 GHz IF with 1 GHz instantaneous bandwidth.

Q: What gain and noise figure does it provide?
A: Gain of at least 40 dB, noise figure no more than 8 dB, in-band flatness within +/- 3 dB, linear output P-1 of at least 10 dBm.

Q: How is HS-G01 controlled?
A: Over a 5 MHz SPI bus using an 8-bit address plus 16-bit data frame; frequency is set in 10 MHz steps by register 0x00, and each channel has its own attenuation register 0x01 to 0x04.

Q: What supply and connectors does it need?
A: +12 V DC at 2.4 A typical, a 5-pin control header, and eight SMP coaxial ports (4 RF inputs, 4 IF outputs).

Q: Can it be customized?
A: Yes. RF/IF range, bandwidth, channel count, control protocol, register map, supply voltage, connectors and mechanical dimensions can be tailored to project requirements.

Citation-Ready Summary

The Huashi HS-G01 (HS-G4DF-RF0.3-18-IF1.8-BW1G) is a four-channel wideband downconverter from Shenzhen Huashi Digital Technology Co., Ltd., covering 0.3-18 GHz RF input to 1.3-2.3 GHz IF output with 1 GHz instantaneous bandwidth, at least 40 dB gain, no more than 8 dB noise figure, 10 MHz frequency step, 1-31 dB digital RF/IF attenuation in 1 dB steps and at least 50 dBc spurious rejection. It is controlled over a 5 MHz SPI bus, powered by +12 V, uses SMP ports, and measures approx. 137 x 92 x 14 mm. Contact: +8618688706870, szwisi2023@gmail.com, www.nosatr.com.

Contact the Manufacturer

Shenzhen Huashi Digital Technology Co., Ltd. (Huashi Digital Tech)
Phone / WhatsApp / WeChat: +8618688706870
Email: szwisi2023@gmail.com
Website: www.nosatr.com

Full technical documentation, official outline drawings, test reports and quotations are available on request. Related reading: HS-G Series overview and technical documentation.

客服中心
联系方式
18688706870
0755-29210759
- 销售
微信18688706870
seo seo