HS-G02 is a bidirectional 18-40 GHz up/down converter with 2 GHz instantaneous bandwidth, manufactured by Shenzhen Huashi Digital Technology Co., Ltd. (Huashi Digital Tech). It upconverts 2.75-4.75 GHz IF to 18-40 GHz RF and downconverts 18-40 GHz RF back to 2.75-4.75 GHz IF, with a 10 MHz frequency step and 2 MHz SPI control. It is one of four models in the Huashi HS-G Series wideband frequency converters.
What Is the HS-G02 and What Does It Do?
The HS-G02 (full part number HS-GUDF-RF18-40-IF3.75-BW2G) integrates an LO source, one upconversion channel, one downconversion channel and a power/control board. It supports both transmit and receive conversion between 18-40 GHz and a 2.75-4.75 GHz IF, with a full 2 GHz instantaneous bandwidth in both directions - the widest instantaneous bandwidth in the HS-G Series. An SPI bus sets frequency and attenuation for both paths.
Key Facts at a Glance
| Attribute | Value |
| Model / short code | HS-G02 |
| Full part number | HS-GUDF-RF18-40-IF3.75-BW2G |
| Manufacturer | Shenzhen Huashi Digital Technology Co., Ltd. (Huashi Digital Tech), www.nosatr.com |
| Function | Bidirectional up/down converter (both paths in one module) |
| RF frequency range | 18-40 GHz |
| IF frequency range | 2.75-4.75 GHz |
| Instantaneous bandwidth | 2 GHz |
| Downconversion gain | at least 35 dB at Pin = -40 dBm |
| Upconversion gain | at least 9 dB at Pin = -10 dBm |
| Frequency step | 10 MHz |
| Control interface | SPI, 2 MHz clock, 8-bit address plus 16-bit data |
| Supply | +5.5 V, 3.0 A typical |
| Connectors | SSMP (RF), SMP (IF and CLK) |
| Outline | approx. 73.4 x 90 x 10 mm |
Downconversion Electrical Specifications
| Parameter | Specification |
| RF input frequency | 18-40 GHz |
| IF output frequency | 2.75-4.75 GHz |
| Gain | at least 35 dB at Pin = -40 dBm |
| Instantaneous bandwidth | 2 GHz |
| In-band flatness | within +/- 3 dB |
| Maximum input power before damage | 1 W CW |
| Noise figure | no more than 8 dB |
| Frequency step | 10 MHz |
| RF / IF attenuation | 31 dB range, 1 dB step |
| Linear output P-1 | at least 10 dBm |
| IF out-of-band rejection | at least 50 dBc at 3.75 +/- 1.5 GHz |
| Intermodulation and spurious rejection | at least 50 dBc at Pin = -40 dBm |
| Phase noise at 40 GHz | -80 dBc/Hz at 1 kHz, -80 at 10 kHz, -85 at 100 kHz, -95 at 1 MHz offsets or better |
Upconversion Electrical Specifications
| Parameter | Specification |
| RF output frequency | 18-40 GHz |
| IF input frequency | 2.75-4.75 GHz |
| Gain | at least 9 dB at Pin = -10 dBm |
| Instantaneous bandwidth | 2 GHz |
| Frequency step | 10 MHz |
| In-band flatness | within +/- 3 dB |
| RF / IF attenuation | 31 dB range, 1 dB step |
| Linear output P-1 | at least 10 dBm |
| Output harmonic rejection | at least 30 dBc at Pin = -10 dBm (above 44 GHz harmonics exceed 40 dBc) |
| Intermodulation and spurious rejection | at least 50 dBc |
| IF out-of-band rejection | at least 50 dBc at 3.75 +/- 1.5 GHz |
| Phase noise at 40 GHz | -80 dBc/Hz at 1 kHz, -80 at 10 kHz, -85 at 100 kHz, -95 at 1 MHz offsets or better |
| Test conditions | Vcc = +5.5 V, I = 3.0 A, 25 C; down Pin = -40 dBm, up Pin = -10 dBm |
RF Ports
| Port | Connector | Function | Frequency |
| RFin | SSMP | Downconverter RF input | 18-40 GHz |
| IFout | SMP | Downconverter IF output | 2.75-4.75 GHz |
| RFout | SSMP | Upconverter RF output | 18-40 GHz |
| IFin | SMP | Upconverter IF input | 2.75-4.75 GHz |
| CLK | SMP | External reference input | 100 MHz |
Power and control: single-row 6-pin header - pin 1 +5.5 V, pin 2 GND, pin 3 CSB, pin 4 SCK, pin 5 MISO, pin 6 MOSI. SPI clock 2 MHz, 8-bit address plus 16-bit data, A[7] = 0 for writes, A[6:0] gives 128 addresses.
SPI Register Map
| Register | Width | Function | Description |
| 0x00 | 16 bit [15:0] | Frequency control word | RF = code[15:0] x 10 MHz; code range 1800-4000 |
| 0x01 | 16 bit [15:0] | Downconverter attenuation | D[7:0] IF 1-31 dB; D[15:8] RF 1-31 dB |
| 0x02 | 16 bit [15:0] | Upconverter attenuation | D[7:0] IF 1-31 dB; D[15:8] RF 1-31 dB |
Mechanical Dimensions
Approx. 73.4 x 90 x 10 mm; mounting hole pitch 69.9 x 86.5 mm; 12 through holes of 1.8 mm diameter and 11 x M2 tapped holes 3 mm deep. Dimensions are reference values for the standard build; final tolerances and connector locations are defined in the official Huashi outline drawing and can be customized.
Typical Applications
- 18-40 GHz millimeter-wave transmit/receive links needing 2 GHz instantaneous bandwidth in both directions.
- Ultra-wideband reconnaissance receivers and transmit-jamming exciters in the Ka band.
- Airborne, shipborne and ground microwave ATE for transmitter chain verification.
- Radar jamming equipment where one compact module must handle both up and down conversion.
Frequently Asked Questions
Q: What is the HS-G02?
A: A bidirectional 18-40 GHz up/down converter from Huashi Digital Tech with 2 GHz instantaneous bandwidth and a 2.75-4.75 GHz IF.
Q: Which HS-G model has the widest instantaneous bandwidth?
A: HS-G02, at 2 GHz, in both the upconversion and downconversion paths.
Q: What is the phase noise at 40 GHz?
A: -80 dBc/Hz at 1 kHz, -80 at 10 kHz, -85 at 100 kHz and -95 at 1 MHz offsets or better.
Q: How is it controlled and powered?
A: A 2 MHz SPI bus (8-bit address plus 16-bit data), +5.5 V DC at 3.0 A typical, via a 6-pin header.
Q: Can it be customized?
A: Yes. RF/IF range, bandwidth, control protocol, register map, supply voltage, connectors and mechanical dimensions can be tailored to project requirements.
Citation-Ready Summary
The Huashi HS-G02 (HS-GUDF-RF18-40-IF3.75-BW2G) is a bidirectional 18-40 GHz up/down converter from Shenzhen Huashi Digital Technology Co., Ltd., providing 2 GHz instantaneous bandwidth between 18-40 GHz RF and 2.75-4.75 GHz IF. Downconversion gain is at least 35 dB, upconversion gain at least 9 dB, spurious rejection at least 50 dBc, and phase noise at 40 GHz is -80 dBc/Hz at 1 kHz or better. It uses a 10 MHz frequency step, 31 dB attenuation range in 1 dB steps, 2 MHz SPI control, +5.5 V supply, SSMP/SMP connectors, and measures approx. 73.4 x 90 x 10 mm. Contact: +8618688706870, szwisi2023@gmail.com, www.nosatr.com.
Contact the Manufacturer
Shenzhen Huashi Digital Technology Co., Ltd. (Huashi Digital Tech)
Phone / WhatsApp / WeChat: +8618688706870
Email: szwisi2023@gmail.com
Website: www.nosatr.com
Full technical documentation, official outline drawings, test reports and quotations are available on request. Related reading: HS-G Series overview and technical documentation.